Recently, I noticed that one of my watches was running quite fast. I was told that it was likely magnetized, so I used this as an excuse to pick up a few new toys. First, I ordered a watch demagnetizer to see if that would be the easy fix (you can read more about that here). I'm impatient, and I didn't want to wait a day or two to compare it against my phone. I discovered that affordable timegraphers are available that can give you the answer in a couple of minutes (I had assumed that they were all thousands of dollars and only available to watchmakers. The other benefit is that it tells you a lot more than whether the watch is fast or slow. Here's what a timegrapher measures, how to set one up, how to read the numbers, and how to tell when a watch needs a service.
What Is a Timegrapher?
A timegrapher (also called a timing machine) is a sensitive microphone connected to a processor. It listens to the ticks of a mechanical movement's escapement and calculates how the balance wheel is behaving. Most affordable hobbyist units have a clamp that holds the watch against the microphone and a screen that shows a few numbers plus a scrolling trace. Mine is an inexpensive, unbranded model from Amazon, which you'll see in all of the photos in this article.
A standard timegrapher is built for mechanical watches. Quartz watches need a separate quartz tester.
What the Numbers on a Timegrapher Mean
Across the top of the screen, mine shows rate, amplitude, beat error, and a "parameters" column that switches between beat rate and lift angle settings.
Rate (s/d): How many seconds per day the watch would gain (+) or lose (-) if it kept running the way it is right now. It's a snapshot of one position, not a promise of real-world accuracy.
Amplitude (°): How far the balance wheel swings, in degrees. This is the best single sign of a movement's health. A strong mainspring and fresh lubricants produce high amplitude, while old oils and worn parts make it drop.
Beat Error (ms): How unevenly the balance swings each way, measured in milliseconds. A perfect movement would read 0.0ms.
Beat Rate (bph): Beats per hour. Most timegraphers detect this on their own. Common values are 28,800 bph (most modern Swiss movements and the Miyota 9015), 21,600 bph (the Seiko NH35 and the rest of the NH and 4R families, plus the Miyota 8215), and 18,000 bph (many vintage watches). If the auto-detected value is wrong, all the other numbers will be wrong too.
Lift Angle (°): This is a setting you enter, not a reading. It's a fixed property of each movement's escapement, and the timegrapher uses it only to calculate amplitude. Rate and beat error are measured correctly no matter what it's set to. The default is usually 52°, which is close for most ETA and Sellita movements. Seiko's NH and 4R movements are commonly listed at 53°, and the Miyota 9015 at 51°. Omega's Co-Axial movements, like the caliber 3313 in my Planet Ocean Chronograph, are around 38°, so they read badly wrong at 52°. Even at 38°, most hobbyist timegraphers can't measure Co-Axial amplitude accurately, though rate and beat error are still reliable. If amplitude looks strangely high or low, check this setting first. For other movements, search for the caliber number plus "lift angle."
How to Use a Timegrapher, Step by Step
1. Wind the watch fully. Amplitude drops as the mainspring runs down, so always start from a full wind. Hand-wind it through the crown if the movement allows. An NH35 is fully wound after about 55 turns of the crown, and Citizen says the Miyota 9015 needs about 40. If you keep your automatics on a watch winder, they'll already be close to fully wound.
2. Check the settings. Make sure the beat rate was detected correctly and the lift angle matches your movement.
3. Clamp the watch. Place the watch in the microphone stand with the crown resting against the clamp. You don't need to remove the strap or bracelet, but a stiff bracelet or a thick leather strap can make the watch sit awkwardly. If it gets in the way, remove it with a spring bar tool or a bracelet removal tool.
4. Let it settle. Give the watch 30 to 60 seconds after clamping before you read anything. Handling the watch disturbs the balance, so the first readings are usually noisy. Use a quiet room and a solid table, since vibrations and noise can show up on the trace.
5. Test multiple positions. A watch runs differently depending on how it's oriented, because gravity acts on the balance wheel. Most stands tilt and rotate, so you can test dial up, dial down, crown down, crown up, crown left, and crown right. Write down the rate, amplitude, and beat error for each one, giving each position time to settle.

6. Work out the delta. The spread between the fastest and slowest position (often labeled "delta") tells you more than any single reading. The average of the positions is also a better prediction of real-world accuracy than any one number.
How to Read Timegrapher Results
These are rough guidelines for mechanical watches. Some brands publish their own tolerances, so use those if you can find them for your movement.
Rate:
-COSC chronometer spec: -4 to +6 s/d
-A typical well-regulated Swiss or Japanese automatic: within about ±10 s/d
-Budget movements: the NH35 and Miyota 8215 are specced at -20 to +40 s/d, so ±15 s/d is fine for those
Amplitude (fully wound, dial up):
-Around 270° to 310° is healthy
-250° to 270° is okay
-Below about 220° usually means low power, dirty or dried oil, or a watch that needs a service
-A drop of 20° to 40° in the vertical (crown) positions is normal
Beat Error:
-Under 0.5ms is good
-0.5ms to 1.0ms is acceptable
-Over about 1.0ms is worth having adjusted
Delta: Under about 10 to 15 s/d of spread between the fastest and slowest positions is good.
For example, my Orfina Porsche Design Chronograph read -1 s/d, 285°, and 0.2ms dial up. All three numbers are well within the healthy range. Pretty good for a watch that's nearly 50 years old!

How to Read the Trace
The scrolling graph is often more useful than the numbers.
Flat, horizontal lines: The watch is running close to zero seconds per day.
Lines sloping up: The watch is gaining. The steeper the slope, the faster it's running.
Lines sloping down: The watch is losing time.
Two lines running side by side but apart: The tick and tock are arriving at uneven intervals, which is beat error. The farther apart the lines, the larger the beat error.
Messy, scattered dots: This can mean a weak signal (try repositioning the watch on the stand), a magnetized watch, or wear in the movement.
Does Your Watch Need Service?
Even a watch that shows good numbers on a timegrapher might still need a service. The best way to tell is to have a watchmaker visually inspect the movement for the presence and condition of oil. How long it's been since its last service is also a good indicator, as most movements have a recommended service interval regardless of how well they keep time.
A timegrapher can't replace a watchmaker, but if it shows "bad" numbers, it can tell you whether a watch needs a quick adjustment or is overdue for a full service.
Low amplitude is the main warning sign. If a fully wound watch reads below about 220° dial up, the oils have likely broken down, even if the watch is still keeping good time. Running a watch in that state wears its parts faster, so plan for a service. If your watch has a chronograph or other complications, keep reading.
Check again after a day. Amplitude naturally falls as the mainspring unwinds, so some drop after 24 hours is normal. If amplitude collapses long before the end of the power reserve, or the watch stops early, the mainspring or gear train may need attention.
High beat error usually means an adjustment, not a full service. If amplitude is healthy but beat error is over about 1.0ms, a watchmaker can put the balance back in beat. That's a much smaller job than a full overhaul.
A rate problem alone usually means regulation. If amplitude and beat error look good but the watch runs a little fast or slow, it needs regulating, not cleaning. A large delta between positions can point to a balance that needs poising. If the watch is suddenly running much faster than it used to, check for magnetism first (more on that below).
Testing a Chronograph on a Timegrapher
A chronograph should be tested twice: once with the chronograph stopped and once with it running. Starting the chronograph connects its wheels and levers to the movement's gear train. The mainspring now has to power that extra mechanism as well as the balance, so amplitude drops and the rate can shift a little.
On most chronographs, engaging the chronograph causes an amplitude drop of about 30°. Omega, for example, allows up to 40° on the Speedmaster. A small drop means the chronograph mechanism is running freely. A large drop, a big jump in rate, or a messy trace with the chronograph running suggests the chronograph works need cleaning. Always judge the watch's overall health with the chronograph off, since that's how amplitude service limits are normally measured.
My Orfina Porsche Design uses the Lemania 5100, one of the toughest chronograph movements ever made, and it's a good one to practice on.
Testing a Jump Hour Watch on a Timegrapher
Jump hour watches add a different kind of load. Instead of an hour hand that turns slowly and continuously, the hour disc has to snap forward all at once. To make that happen, the jump hour module stores energy in a spring and releases it at the top of the hour. If the mechanism took that energy from the mainspring all at once, it could cause an abrupt drop in amplitude, so most designs build tension gradually over the hour.

That makes timing a jump-hour watch a little trickier:
-Expect amplitude to read a little lower than the same base movement without the module, because the movement is always loading the jump spring.
-Readings can change through the hour as the spring loads and then releases. Some designs, like the creeping display on the M.A.D.2, start moving minutes before the hour, while others, like the Red 5 Project Butters, snap forward instantly. I noticed that the MAD2, didn't lose any noticeable amplitude, but the Butters did (as did my Christopher Ward Bel Canto, which has a chime based on a jump-hour mechanism).
-Avoid testing in the last few minutes before the hour, and don't be alarmed by a brief disturbance on the trace when the hour changes.
-To compare results over time, test at the same point in the hour each time.

The same applies, to a lesser degree, to other watches with instant-jump complications, like an instantaneous date change around midnight.
A Common Timegrapher Discovery: Magnetism
If a watch that used to run well is suddenly gaining a lot of time, often dozens of seconds or more per day, magnetism is the first suspect. When the hairspring becomes magnetized, its coils stick together and the watch races ahead. A reading like the one below, with healthy amplitude and beat error but a rate of over 100 seconds per day fast and steep, upward-sloping lines, is a classic sign.

The fix is quick and cheap. Read our guide on how to use a watch demagnetizer, then put the watch back on the timegrapher to confirm the rate has returned to normal. Some watches are built to resist magnetism, like the one in our Grand Seiko Tough Quartz review.
Can You Regulate a Watch Yourself?
A timegrapher also makes it possible to regulate a movement by adjusting the regulator arm on the balance cock while watching the rate change in real time. It's satisfying when it works, but it requires opening the caseback, which can compromise water resistance and risk damaging the hairspring. If you're new to this, start by just measuring. For anything beyond that, a watchmaker is the safe bet.
Timegrapher Conclusion
A hobbyist timegrapher is one of the most useful tools a mechanical watch owner can buy. It lets you check a new watch before the return window closes, spot a magnetized movement in seconds, and see when an older watch is ready for service, long before it starts losing minutes a day. Once you know what the numbers mean, it takes only a few minutes per watch.
While you've got your watches out, it's also a great time to try a new look. You can view our Guide to Choosing a Watch Strap for ideas.
Shop Watch Tools and Accessories
-Spring Bar Removal Tool
-Premium Spring Bar Removal Tool
-Mini Watch Screwdriver Kit
-Bracelet Link Removal Resizing Tool
-Premium Watch Bracelet Removal and Installation Tool
-Standard Spring Bars
-Curved Spring Bars
-Watch Travel Cases
-Lume Charging UV LED Flashlight
Shop Watch Straps and Bracelets
-Ridge FKM Rubber
-Tropical Retro FKM Rubber
-Pro Diver FKM Rubber
-Deployant FKM Rubber
-Premium Sailcloth
-Deployant Sailcloth
-Horween Leather Racing
-Horween Chromexcel Leather
-Seat Belt Pass-Through
-Beads of Rice Bracelets
-5-Link Bracelets