How to Use a Watch Demagnetizer (and Tell If Your Watch Is Magnetized)

How to Use a Watch Demagnetizer (and Tell If Your Watch Is Magnetized)

I recently discovered one of my watches was fast by several minutes, even though I had just set it a few days earlier. It seemed likely that it was magnetized, so I decided to see if an inexpensive demagnetizer could fix it without me sending it away for service. Here's how to tell if your watch is magnetized and how to use a demagnetizer correctly.

Blue box-style watch demagnetizer with a red push button and power light, next to a small compass

Why Magnetism Affects Mechanical Watches

The heart of a mechanical movement is the balance wheel and its hairspring, a tiny coiled spring that breathes in and out several times per second. When the steel parts of a movement are exposed to a strong magnetic field, the hairspring can become magnetized. Its coils start sticking together, effectively shortening the spring and making the balance swing faster. The result is a watch that gains time, often a lot of it.

Magnets are everywhere today. Phones, laptops, tablets and their cases, speakers, headphones, magnetic bag clasps, and even some refrigerator doors can all do it. Leaving a watch next to any of them overnight is a common way to magnetize it. When you travel, keeping your watches in a watch travel case instead of loose in a bag next to your laptop and tablet helps keep them away from those magnets.

What About Anti-Magnetic Watches?

A watch can be marked "antimagnetic" under ISO 764 if it resists a magnetic field of 4,800 A/m. To pass, a mechanical watch with a normal-sized movement can't stop during the test, and its rate can't shift by more than 30 seconds per day afterward. That protects against everyday exposure, but not against strong magnets. Some watches go much further, using soft-iron inner cases or non-magnetic materials. We tested one of them in our Grand Seiko Tough Quartz SBGX341 review, and you can find more in our anti-magnetic watch reviews. If you'd like to dig even deeper into magnetism and watches, check out this article I wrote a few years ago.

Quartz watches are less vulnerable. ISO 764 allows a quartz watch a residual effect of only 1.5 seconds per day after the same test. A strong field can still stall a quartz watch's stepper motor while it's exposed, but the watch normally recovers once the magnet is removed.

How to Tell If Your Watch Is Magnetized

The compass test: Place a small compass on a flat table, away from electronics, and let the needle settle. Slowly move the watch around the compass about an inch away. If the needle swings toward the watch and follows it, the watch is magnetized. If it barely moves, magnetism probably isn't your problem.

The phone test: No compass? Free magnetometer apps use the magnetic sensor already in your phone and will show a spike when a magnetized watch gets close. Keep in mind that the phone itself contains magnets, so don't leave the watch sitting on it.

The timegrapher test: If you have a timegrapher, a magnetized watch will usually show a sudden, large positive rate and steep, upward-sloping trace lines, even when amplitude and beat error look healthy. See our guide on how to use a timegrapher to help you read the results. It's also the best way to confirm the fix worked.

Weishi No. 1000 timegrapher reading +137 s/d, 280°, 0.2ms at 21,600 bph, with steep upward-sloping trace lines

How to Use a Box-Style Watch Demagnetizer

The most common demagnetizer is a small, often blue, plastic box with a flat top and a single push button. Inside is a coil that creates a rapidly alternating magnetic field. The key is that the field must fade away gradually as you move the watch away. That decaying, back-and-forth field scrambles the magnetism in the steel parts until nothing is left.

Blue 110/220V box-style watch demagnetizer sitting on its instruction sheet

1. Take the watch off your wrist. Some brands recommend letting the watch stop and pulling out the crown first, but many people demagnetize a running watch without issue.

2. Place the watch on the demagnetizer pad, or hold it just above it.

3. Press and hold the button. You'll hear a buzz, and most units have a light that shows they're on.

M.A.D.2 held just above the pad of a blue box-style demagnetizer

4. Slowly lift the watch straight up and away while still holding the button. Move it in one smooth, steady motion until it's at least a foot (30cm) away. Many people go a full arm's length, about two feet (60cm), to be safe.

5. Release the button only after the watch is far away. This is the most common mistake. If you release the button while the watch is still on the pad, the field shuts off at full strength, and the watch can end up just as magnetized as before.

6. Test again. Repeat the compass test. Most watches clear on the first pass. If the needle still moves, rotate the watch 90 degrees on the pad and repeat.

The watch in the photo above is the M.A.D.2 with its strap removed, but you don't need to take off the strap or bracelet to demagnetize a watch.

How to Use a Tunnel-Style Demagnetizer

Some demagnetizers have a tunnel or loop instead of a flat pad. The idea is the same. Press and hold the button with the watch outside the tunnel, slowly move it into the center, rotate it for a few seconds, then slowly pull it out and away to arm's length before releasing the button.

Demagnetize Your Tools Too

Steel tweezers and screwdrivers can become magnetized and pass that magnetism on to the parts they touch. A magnetized tip can also make tiny screws jump to the tool. Run your watch screwdrivers, spring bar tool, and bracelet link tool through the same process every so often.

When a Demagnetizer Won't Fix It

If the compass test shows no magnetism and the watch is still running far outside its normal rate, something else is going on. Old lubricants, a damaged hairspring, or a knock to the movement can all cause similar symptoms. A timegrapher can help you tell the difference. Low amplitude or high beat error points to a movement that needs a watchmaker.

Demagnetizer Conclusion

A demagnetizer is one of the cheapest and most useful tools a mechanical watch owner can keep in a drawer. A ten-second compass check and a slow, steady pass over the pad can save you a service bill and get a fast-running watch back to normal. Just remember the golden rule: keep holding the button until the watch is well away from the demagnetizer.

Once your watch is running right again, it's a great time to give it a fresh look. You can view our Guide to Choosing a Watch Strap for ideas.

Shop Watch Tools and Accessories

-Spring Bar Removal Tool
-Premium Spring Bar Removal Tool
-Mini Watch Screwdriver Kit
-Bracelet Link Removal Resizing Tool
-Premium Watch Bracelet Removal and Installation Tool
-Standard Spring Bars
-Curved Spring Bars
-Watch Travel Cases
-Lume Charging UV LED Flashlight

Shop Watch Straps and Bracelets

-Ridge FKM Rubber
-Tropical Retro FKM Rubber
-Pro Diver FKM Rubber
-Deployant FKM Rubber
-Premium Sailcloth
-Deployant Sailcloth
-Horween Leather Racing
-Horween Chromexcel Leather
-Seat Belt Pass-Through
-Beads of Rice Bracelets
-5-Link Bracelets

0 comments

Follow Us On Our Socials